Call the hotline:0755-21030087

Business hours:9:00-18:00

Shenzhen Haomingfei Technology Co., Ltd.
Abstract: Quick start ballast bulb

Quick start ballast bulb


The characteristics of xenon lamps compared with ordinary halogen bulbs: high brightness, using the same wattage HID, the brightness is about 23 times that of tungsten filament lamps. Although the luminous arc of a xenon lamp has the same length and diameter as the tungsten filament of a halogen lamp, the luminous efficiency and brightness are improved nearly

  • Product details page

  • Additional product information

Xenon bulb:
It refers to a high-pressure gas discharge lamp that is filled with a mixture of inert gases including xenon and does not have the filament of a halogen lamp. HID xenon lamp for short. It can be called a metal halide lamp or a xenon lamp. Use xenon lamps and xenon lamps for outdoor lighting.
Bulb type:
The models of xenon lamps are divided into bulbs, generally divided into three series: 900 series, H series and D series. (D series is usually lens series)
Lamp holder model:
The HID model and the halogen bulb are one-to-one correspondence, that is, what model is the original halogen bulb, then the same model must be used when refitting the HID.
H series: H1, H3, H4, H6, H7, H8, H9, H10, H11, H13, etc.;
90 series: 9004 (HB1), 9005 (HB3), 9006 (HB4), 9007 (HB5), etc.;
D series: D1S, D1C, D1R, D2R, D1C, D2C, D3C, D4C, etc.;
Other: 880, 881
Models such as H1, H4, H7, 9005, 9006, 9007 are more commonly used in automotive HID.
Bulb color temperature:
  Modified xenon lampThe color temperature ranges from 3000K to 12000K. The color temperature of 6000K is similar to sunlight, but contains more green and blue components, so it presents blue-white light. This blue-white light greatly improves the brightness of road signs and signs. Therefore, 6000K color temperature bulbs are generally chosen.
The advantages of xenon lamps:
1. The brightness efficiency of HID is three times higher than that of halogen lamps, which has obvious effect on improving the visibility of driving at night and in fog.
2. The luminous flux emitted by the xenon lamp is more than twice that of the halogen lamp, and the efficiency of converting electric energy into light energy is also 70% higher than that of the halogen lamp, so the xenon lamp has a relatively high energy density and light intensity. The increase in the brightness of car lights also effectively expands the visual range in front of the car, thereby creating safer driving conditions.
3. Power saving 1/2, halogen lamp consumes more than 60W of power, xenon lamp only needs 35W of power.
4. Because the xenon lamp has no filament, it will not cause the problem of scrap due to broken filament. The service life is much longer than that of the halogen lamp. The service life of the xenon lamp is equivalent to the entire operating time of the average car cycle.
5. Once the xenon lamp fails, it will not be extinguished instantaneously, but will be extinguished by gradually dimming (or quickly lit), so that the driver can win time in the dark driving and stop urgently.
Installation Precautions:
1. Do not install the ballast next to the heating element. Generally, it can be installed on the bumper to help dissipate heat.
2. Do not install the ballast near some wires, or near the water source; such as near a water tank. (Excessive humidity will cause leakage and aging of the ballast)
3. Place it in a place with good air permeability so that air can flow to lower the temperature of the ballast. After installation, the relay and fuse on the wire set are generally exposed for easy replacement.
4. The high-voltage line of the ballast is not easy to wind, so as not to generate an excessive magnetic field, which may affect other electrical equipment of the car. Install the ballast connection point downwards.
5. Ensure that the bulb is sealed after installation.
6. During installation, the dedicated cable set is generally tight and may be beautiful. Don't connect it with the heating element, so as to avoid short circuit and open circuit caused by the high temperature. Use cable ties to tie it up, and do not contact with mechanically moving parts, causing unnecessary contact.
7. All interfaces and fuses should be tied up with electrical tape to avoid loosening and poor contact.
8. When the lamp is installed, one side will not light up or will flash. Generally, adjust the position of the negative pole of the dedicated cable set first.
9. Install the H4 model light. If it is not on when it is on, it will not light, and it will flash continuously, first check whether the positive and negative poles of the H4 wiring match. Generally, there are two types: ++- and --+, matching Good will return to normal.
10. Sometimes when you encounter a car with a positive frame, you need to wrap the ballast with Jedi glue so that the ballast will work.
11. After installation, if there is no dedicated line installed, in order to avoid excessive current when starting to blow the original car fuse, the original car control fuse should be replaced by more than 20A.

Related News

Product Recommended

  • 12V quick start highl...
  • 24V ballast for trucks
  • Decoding ballast HZ
  • Quick start ballast bulb
  • Dianwei quick-start h...
  • Quick start highlight...

电话: 18194062866手机:0755-21030087邮箱

|   Mobile